XenonZcar Banner
Shop
XenonZcar Full Service Shop

Z31 Nistune ECU Tuning

Nistune turns the stock Z31 engine computer into a fully tunable one. This page covers what it is, how we install the board, which base ROM to start from, and where to get it done.

What Is Nistune?

Nistune is a tuning system for Nissan engine control units (ECUs). A small daughterboard goes inside your factory ECU, and from then on the fuel, ignition timing and other maps can be changed from a laptop running the Nistune software. Changes take effect live, with the engine running, so a tuner can dial in the car on a dyno or on the road.

It gives you much of what a standalone aftermarket ECU does for far less money, and you keep the factory wiring harness and sensors. Once the board is installed it stays in the ECU for good.

The Z31 uses the Nistune Type 1 board, which connects to your laptop through a USB port added to the ECU case.

Nistune Type 1 board installed in a Z31 ECU

A finished Type 1 install in a Z31 ECU.

Get It Installed at XenonZcar

We install Nistune Type 1 boards in Z31 ECUs at our shop in Mount Carmel, PA. Drop off your ECU or ship it to us, and we handle the soldering, socket, wiring and USB port, plus the MAF signal mod if you need it.

We do the install only, not the tuning. Once it's back in your car, take it to a Nistune tuner (see the list below) or tune it yourself.

Email us for current pricing and turnaround before you send anything.

Installing the Nistune Board Yourself

If you can solder, you can do this install at home. I did my own. Read the whole guide before you start, and work on a clean, static-safe bench.

Before you start: keep the original ROM chip you remove. It's your stock tune, and you'll want it if you ever go back to stock. Desolder slowly with a pump or wick: too much heat lifts the pads and traces off these old boards.

1. Open the ECU

Remove the four screws on the front cover and the four on the back cover. Go easy: on an ECU that has seen water or road salt the screw heads strip easily.

Z31 ECU with the cover removed

2. Find your ECU's layout

The board looks different depending on the year. Find yours below; the parts you'll be working on are circled.

1984-1985 Z31 ECU, two-board layout opened up
1984-85: the ECU opens up into two boards.
1984-1985 ECU with the parts to remove circled
1984-85: parts to remove circled.
1986 Z31 ECU
1986 ECU.
1986 ECU chips close up
1986: the chips close up.
1986-1987 non-turbo Z31 ECU opened up
1986-87 non-turbo ECU.
1987 Z31 ECU with the ROM circled
1987: the ROM is circled.
1988-1989 Z31 ECU with the ROM and wiring pads circled
1988-89: the ROM and the four wiring pads are circled.

3. Clean off the factory coating

Nissan sprayed the boards with a lacquer to protect them from moisture. Solder won't take through it, so clean every spot you'll be soldering or desoldering with acetone first.

Back of a 1984-1985 ECU board with the areas to clean circled
Back of an 84-85 board: clean the circled solder joints.
Front of a 1984-1985 ECU board with chips circled
Front of an 84-85 board.

4. Remove the ROM and fit a socket

Desolder the factory ROM and solder a 28-pin socket in its place. The Nistune board plugs into this socket.

28-pin socket installed where the ROM was on a 1984-1985 ECU
84-85: socket installed where the ROM was.
Close-up of the 28-pin socket on a 1984-1985 ECU below the HD6802 CPU
84-85: the socket close up, just below the CPU.
ECU with the ROM socket installed
Socket installed on a later ECU.

5. Solder the four wires

The Nistune board needs four extra signals from the ECU's processor. On the 1984-86 ECUs these come straight off the HD6802W CPU's pins:

WireCPU signalHD6802W pin
1R/W34
2A1424
3A1525
4E37
HD6802W CPU pinout with the four Nistune wire points marked
HD6802W pinout with the four wire points marked.
Four wires soldered to the HD6802W CPU on an early ECU
Early ECU: wires 1-4 soldered to the CPU.
Four wires soldered to the pads on a 1988-1989 ECU
1988-89: the wires go to the four pads next to the socket.

6. Add the USB port

Cut an opening in the ECU case for the board's USB connector and mount it with two screws, so you can plug in a laptop without opening the ECU again.

USB port mounted in the side of the ECU case
The USB port from outside the case.
USB connector mounted inside the ECU case
The same port from inside.
Switch mounted through the ECU case
Optional: a switch mounted through the case.

7. MAF signal mod (if needed)

The factory ECU caps how high it will read the mass airflow (MAF) sensor signal. If you're running a larger MAF, such as the Z32 unit, or more airflow than stock, the ECU needs a small change so it can see the full signal.

1984-86 ECUs: find the small surface-mount op-amp board. Heat the top of pin 14 on its right-hand side and push the pin away from the mini board with a small flat screwdriver. It only has to lose contact with the mini board; you don't need to pull it out of the ECU. With this method the older zener diode mod isn't needed.

Later ECUs: remove the two parts marked in the photo below.

Op-amp mini board on an early ECU with pin 14 circled
1984-86: pin 14 of the op-amp board is circled.
Later ECU with the two parts to remove for the MAF mod marked
Later ECUs: remove the two marked parts.

8. Plug in the board and test

Plug the Nistune board into the socket, check every joint for bridges, and make sure no wire is pinched before you close the covers. Connect a laptop over USB and confirm the Nistune software sees the ECU before the car goes to the tuner.

For the board itself, follow the install sheet and software guide on nistune.com.

Which Base ROM to Start With

Match the part number on your ECU's label (23710-xxxxx) to find the Nistune base ROM to start from. All of these use the Type 1 board.

Nissan ECU numberBase ROM (BIN)Nistune board
23710-01PXXZ31_EARLY_VG30Type 1
23710-02PXXZ31_EARLY_VG30Type 1
23710-06PXXZ31_EARLY_VG30 or Z31_LATE_VG30Type 1
23710-10PXXZ31_EARLY_VG30Type 1
23710-18PXXZ31_MID_VG30Type 1
23710-21PXXZ31_LATE_VG30Type 1
23710-25PXXZ31_LATE_VG30Type 1
23710-26PXXZ31_LATE_VG30Type 1
23710-545XXZ31_LATE_VG30Type 1
23710-87EXXJ30_VG30EType 1
23710-98EXXJ30_VG30EType 1

Bigger Injectors and the K-Value

Nissan ECUs use a single number, the K-value (injector constant), to turn measured airflow into injector pulse width. Change the injectors or the MAF and the K-value has to change too, or every fuel map is off by the same amount.

For an injector swap, a good starting point is to scale the K-value by the ratio of the injector sizes, at the same fuel pressure:

new K = stock K × (stock injector cc ÷ new injector cc)

For example, going from 260cc to 450cc injectors cuts the K-value to about 58% of stock. Read the stock K-value from your own ROM in Nistune rather than using a number from someone else's car, since it varies by ECU. New injectors also need their own latency (dead time) setting.

A different MAF, such as a Z32 or Ford Cobra unit, changes the airflow reading as well. Load the matching MAF table in Nistune, then fine-tune the K-value on a wideband O2 sensor.

K-Value Reference Table

K-values and latencies owners have reported running with Nistune. The K-value depends on the whole setup, especially the MAF, so use these as a sanity check, not a tune. Fuel pressure is the base pressure with no vacuum; blank means stock or not reported.

Latency tip: enter the injector's latency (dead time) as rated at 14 volts. Injector makers and data sheets usually list it at several voltages; 14 V is the one Nistune expects.

InjectorSizeFuel pressureK-valueLatency (µs)Setup notesSource
Bosch 0280150400Stock3437501986 Z31 VG30 ECU; idles wellNistune forum
Mercedes (Bosch)420ccabout 375Nistune forum
Unnamed420cc37679*Z31 turbo, T3/T4, Walbro 255 pump; rich up top, still being tunedNistune forum
Ford green top440cc37 psi11957*Ford Lightning MAF, Walbro pump, Aeromotive regulator, 24° base timingXenonZcar
Nissan R32 GT-R440ccStock343XenonZcar
Nissan GT-R444ccabout 740Nistune forum
DSM (blue top)450cc37 psi (stock regulator)143770Walbro pump, Ford Cobra MAFXenonZcar
DSM450cc690Rated latency at 14 VNistune forum
Mazda460cc390800XenonZcar
Mitsubishi Evo yellow (MDL510), low impedance510cc696Rated latency at 14.1 VNistune forum
Mazda FC3S RX-7 (Denso), high impedance550cc37 psi330750Mostly stock 88 tune; stock regulator, lines, MAF, pump and turbo at 14-15 psi; 3" exhaust; Schneider stage 1 camsXenonZcar
Bosch720ccabout 1,000Nistune forum

* Older Nistune versions showed latency as a raw number instead of microseconds, so these two can't be compared with the rest.
XenonZcar data compiled by Jason Butts (Jason84NA2T) from members' reports. Nistune forum data from owners' posts in the Latency + K Values thread. Have numbers from your own car? Email sales@xenonzcar.com and we'll add them.

This only gets the car close enough to start tuning. Always confirm the air/fuel ratio with a wideband before any full-throttle runs.

Owners have shared tunes for these setups in the BIN database below:

  • DSM 450cc injectors, stock MAF, 37 psi base fuel pressure, T3/T4 at 10 psi
  • DSM 450cc injectors, Z32 blow-through MAF, 40 psi base fuel pressure, 87 NA ECU
  • DSM 450cc injectors, Z32 MAF, Holset HX35 at 15 psi
  • 440cc injectors with a Cobra MAF on an 88 NA ECU
  • 750cc injectors with a Cobra MAF on a VG30E

BIN File Database

Download tunes other owners have shared, or upload your own to share with the community. These are user tunes, not factory ROMs, so check any file on a dyno before you drive on it.

Nistune Dealers, Installers and Tuners

Shops that install or tune Nistune on Z31s. To be added to this list, email sales@xenonzcar.com.

ShopLocationServices
XenonZcar 17 South Willow Street, Mount Carmel, PA 17851 Board installs (no tuning)
JE Import Performance 6600 Moravia Park Drive, Suite A, Baltimore, MD 21237 2WD and 4WD dyno tuning

Nistune's Official US Workshops

Nistune keeps its own list of US workshops and distributors. Shops that call out Z cars are marked. Phone numbers and contacts are on Nistune's US workshop page, so check there for the latest before you call.

ShopLocationTypeNotes
47point9South CarolinaDistributorJDM vehicles and parts
AutoVaughn PerformanceMurfreesboro, TNDistributor
Concept Z PerformancePhoenix, AZWorkshop and distributorZ specialist
Custom Car PerformanceRockaway, NJWorkshop
Houston Z AutoHouston, TXWorkshop and distributorZ specialist
Natural AspirationsTorrance, CAWorkshop
Peak Innovation MotorsportsVancouver, WAWorkshop and distributor
Performance and StylingManchester, CTWorkshopFull install and dyno tuning
Performance Race EngineeringPortland, ORWorkshop
Phantasm MotorsportsRaleigh, NC
Specialty-ZChatsworth, CADistributorZ specialist
Whites Import AutomotiveRockledge, FLWorkshopNissan tuning
Z1 MotorsportsCarrollton, GAWorkshopZ specialist, mainly 1990 and later
ZShackHouston, TXZ specialist
ZSportEverett, WAWorkshopZ specialist; tunes Z31 and Z32 300ZX

Sources