Z31 Intake Manifold Clean-Up: EGR, Idle Air Control and Air Regulator Delete
The top of the Z31 intake is crowded with emissions and idle control parts: the EGR valve and its tube, the idle air control valve and the air regulator, plus their hoses, wiring and vacuum lines. Removing them and capping the ports with block-off plates cleans up the engine bay a lot.
It isn't free, though. These parts control the idle and cold start, so the car behaves a little differently without them. This page covers how to remove each one, and the problems you may run into and how to fix them.
The XenonZcar Block-Off Plate Kit
The plates and the manifold plug, with the bolt size for each.
| Part | Bolts | Seal |
|---|---|---|
| EGR block-off plate, 3/16" aluminum | 2 × M8 × 1.25 | New EGR gasket, Nissan 14719-W7000 |
| Idle air control valve block-off plate, 3/16" aluminum | 3 × M6 × 1.0 | New IAC gasket, Nissan 23785-D5720 |
| Air regulator block-off plate, 3/16" aluminum | 2 × M6 × 1.0 | RTV or gasket material |
| Stainless exhaust manifold plug (for the EGR tube port) |
The optional bolt kit has the stainless socket cap screws and washers for all three plates. Gaskets aren't included; get them from a Nissan dealer.
Buy the kit in our storeRemoving the Parts
Work on a cold engine and disconnect the negative battery cable first. Label every hose and connector as you go; the factory vacuum diagram on the underside of the hood and the factory service manual help here.
EGR valve
- Disconnect the vacuum hose from the EGR valve.
- Unbolt the EGR tube from the valve and from the exhaust manifold, and remove the tube.
- Remove the EGR valve, then remove its two studs (two nuts locked together on a stud make it easy to back out).
- Install the block-off plate with a new EGR gasket and the two M8 × 1.25 bolts.
- Thread the stainless plug into the exhaust manifold where the EGR tube was. A little anti-seize on the threads helps it come out later.
- Cap or remove the vacuum lines that fed the EGR valve and its control parts.
Idle air control valve
- Unplug the valve's connector and disconnect its hoses.
- Unbolt the valve and clean the mounting surface.
- Install the block-off plate with a new IAC gasket and three M6 × 1.0 bolts.
- Cap any hose ports left open, and tape up the loose connector so it can't short.
Air regulator (cold start valve)
- Unplug the connector and disconnect the two air hoses.
- Unbolt the air regulator.
- Install the block-off plate with RTV or gasket material and two M6 × 1.0 bolts.
- Cap the open hose ports and tape up the connector.
Set the idle
With the idle air control valve gone, the ECU can no longer set the idle, so you set it by hand. Warm the engine fully, then turn the throttle stop screw on the throttle body until it idles at about 1,000 rpm.
Problems and Fixes
- Idle drops or the engine stalls with the A/C, headlights or a hard steering turn
- The idle air control valve used to add air to hold the idle under these loads; the plate takes that away. Set the warm idle a little higher, around 1,000 rpm, so it has some margin. If it still stalls with the A/C on, raise it a bit more.
- Hard cold starts, or a low, rough idle until it warms up
- The air regulator and idle air control valve both raised the idle when the engine was cold. Without them, give it a little throttle for the first minute and let it warm up before driving. In a cold climate, consider keeping the air regulator.
- High or hunting idle, or a lean idle, after the job
- Almost always a vacuum leak: a hose left open, a missing cap, or a plate that isn't sealing. Recheck every hose you disconnected, use new gaskets, and a smoke test finds leaks quickly.
- Idle won't settle, or decel feels wrong after setting the idle
- The throttle switch's idle contact is probably open now. Adjust the throttle switch so it closes at the new throttle stop position.
- Pinging (detonation) at light throttle or cruise
- EGR lowers combustion temperature at part throttle, and without it some engines ping. Use premium fuel, make sure base ignition timing is set to the factory spec, and if the car has Nistune, a tuner can take a little timing out at cruise.
- Check engine light or a stored code
- Some Z31s, mainly California models, monitor the EGR system and may log a fault once it's removed. Read the codes from the ECU to make sure that's the only one before chasing anything else.
- Exhaust leak or ticking at the manifold
- The EGR port plug isn't sealing. Check it's tight; anti-seize on install keeps it from seizing later.
Sources
- 1984-1989 Nissan 300ZX factory service manuals
- XenonZcar block-off plate kit instructions