XenonZcar Banner
Shop
XenonZcar Full Service Shop

Z31 Tension Rods: 1984-87 vs 1988-89

The tension rods locate the front lower control arms front to back. Each rod bolts to the bottom of the control arm at one end, and at the other end it's held in a bracket bolted to the chassis. Worn tension rod bushings cause clunks over bumps, shimmy under braking, and caster that changes as the car moves.

Nissan changed the design for 1988-89, and the two styles use different bushings.

The Two Designs

1984-87: through-bracket bushings

The threaded front end of the rod passes through a hole in the bracket, with a rubber bushing on each side and a nut on the end. This is the same basic layout as the 240Z through 280ZX. The bushings are cheap and easy to replace, but the rod can move a little fore and aft as the rubber compresses.

1984-87 Z31 tension rods passing through their brackets with bushings on both sides
1984-87: the rod passes through the bracket, with a bushing on each side.
1984-87 Z31 tension rods and brackets, other side
The early rods and brackets from the other side.

1988-89: pressed-in bushing

The front end of the rod has an eye with a bushing pressed into it, mounted on a bolt through the bracket. This locates the rod more firmly, but the factory bushing is molded to its center sleeve and pressed into the rod, so it's harder to replace, and Nissan has discontinued it.

1988-89 Z31 tension rods and brackets from the top and bottom, showing the pressed-in bushing eye
1988-89: the bushing is pressed into an eye on the rod.
1984-871988-89
Front bushingTwo-piece, one each side of the bracketOne-piece, pressed into the rod eye
Rod-to-control-arm studsM10 × 1.5M12 × 1.5
Bracket-to-chassis boltsM10 × 1.25, all years
Tension rod nut torque (control arm)65-80 ft-lb

Fastener sizes are from our nuts and bolts chart; the torque is from our front control arm guide.

Bushing Options

PartFitsNotes
Urethane strut rod bushing kit, Z Store 23-20491984-87Four bushings and two collars, enough for both sides.
Tension/compression rod kit, Z Store 23-41901984-87Replaces the forward bushings with a ball-and-socket joint. You still need bushings for the other side of the bracket.
Urethane strut rod bushing kit, Z Store 23-20501987-89 (late style)Two-piece bushings with collars. No pressing, so much easier than the factory part.
Factory forward tension rod bushing, Z Store 23-43251988-89Discontinued by Nissan and expensive; two needed.

Part numbers are from The Z Store; check fitment and current prices with them before you order.

Rubber or urethane? Urethane stops the rod from moving and sharpens the steering, but it rides harsher and can squeak. On a street car, many owners stay with rubber on at least one side.

Swapping an Early Car to the Late Rods

Some 1984-87 owners fit the 1988-89 rods and brackets for the firmer pressed-in bushing. The brackets bolt to the chassis with the same M10 bolts on all years. What to check:

  • The control arm end. The studs grew from M10 to M12 for 1988-89. Make sure the late rods match your control arms' studs and holes before you install them, or use 1988-89 control arms with them.
  • Swap them as sets. Use the rod and bracket together, left and right from the same style.
  • Bushings. Used late rods usually need new bushings; the 23-2050 urethane kit is the easy option.
  • Alignment. The tension rods set caster, so get an alignment after any tension rod work.
The tension rods carry braking loads. Use new nuts where the factory used locking nuts, torque everything to spec with the car's weight on the wheels, and recheck after the first few drives.
Tension rod nuts on the bottom of a Z31 front lower control arm
Tension rod nuts on the bottom of the control arm (17mm).

For full removal steps, see our front control arm and front suspension reconditioning guides.

Sources